Skip to content
A&G EquipmentA&G Equipment

Scissor Lifts

How to Protect Finished Floors When Using a Scissor Lift Indoors

By Jonah Tan, Equipment Specialist · · 3 min read

A&G Equipment Dingli JCPT1212HA electric scissor lift parked on protection boards over a blue sheet inside a finished interior

Hotel lobbies, showrooms, malls and high-end homes often need work at height after the floor is already finished. A scissor lift is the right tool, but one careless move can scratch marble, dent timber or crack tiles. Here is how to plan it so the floor looks the same when the machine leaves.

The photo above shows one of our Dingli JCPT1212HA electric scissor lifts set up the right way: a protective sheet on the floor, then rigid protection boards on top, under the machine and along its route.

1. Choose a battery scissor lift

For finished interiors, always use a battery (electric) scissor lift. Battery machines are quiet, give off no fumes and run on non-marking tyres. Diesel rough-terrain models are for outdoor sites. For most indoor work, the Dingli 12m Electric Scissor Lift covers high ceilings and atriums, and the compact Dingli 5.6m Battery Scissor Lift suits low ceilings and tight rooms.

2. Plan the route in

  • Measure every door, corridor, ramp and goods lift on the way from the loading area to the work area. The machine has to fit through the narrowest point.
  • Check the goods lift rating against the machine’s weight. Ask us for the exact figure before booking.
  • Look for thresholds, steps and floor joints that need a ramp or boards to cross.

3. Check the floor can take the load

A scissor lift puts its weight through four small tyre patches. On solid ground-floor slabs this is rarely a problem, but raised floors, mezzanines, suspended slabs and glass or timber floors need a check against the machine’s weight and wheel loads. If in doubt, ask the building owner or engineer.

4. Lay protection in two layers

  1. A protective sheet first, to catch dust, grit and any drips.
  2. Rigid boards on top, such as film-faced plywood, along the whole travel route and under the working position. Boards spread the wheel load and stop grit from being ground into the floor.

Tape the board joints so the wheels roll smoothly and nobody trips, and keep the boards flat and level so the machine is level when it lifts.

5. Keep it clean while you work

  • Wipe the tyres before the machine comes onto the finished floor.
  • Drive slowly and avoid turning on the spot on soft stone and timber.
  • Keep tools and materials in the platform tray, not on the floor around the machine.
  • Charge the machine in an agreed area, away from finished surfaces.

6. Do the daily checks

Run through our scissor lift pre-use inspection checklist at the start of every shift, and use our scissor lift height guide to pick the right size before you book.

Renting a scissor lift for indoor work

All our scissor lifts come serviced, with a valid PMA, operator training and 24/7 breakdown support for rental customers, delivered to Johor, KL & Selangor. Rates are on enquiry. See our scissor lift rental Johor page, or WhatsApp us with the floor type, ceiling height and access route, and we will recommend a machine.

FAQs: scissor lift floor protection

Will a scissor lift mark a finished floor?
Battery scissor lifts run on non-marking tyres, so they do not leave the black marks that standard rubber tyres do. Grit stuck in the tyres can still scratch soft stone or timber, so clean the tyres and lay protection boards on delicate floors.
What should I put under a scissor lift to protect the floor?
Lay a protective sheet first, then rigid boards such as film-faced plywood over it along the travel route and where the machine works. The boards spread the wheel load and stop grit and drips reaching the floor.
Can a scissor lift be used on a raised floor or mezzanine?
Only after the floor's load capacity has been checked against the machine's weight and wheel loads. Ask us for the machine weight before booking, and check with the building owner or engineer.
Do battery scissor lifts give off fumes indoors?
No. Battery scissor lifts are zero emission where they work, which is why they are used in malls, hotels, offices and data halls.

Machines we recommend for scissor lift floor protection

More guides related to scissor lift floor protection

Need a quote? We usually reply the same day.

Rates on enquiry · Aerial lifts delivered with PMA · Johor, KL & Selangor

Quick quote

Rates on enquiry. We usually reply the same day.